Errol62 wrote: ↑Mon Aug 21, 2023 8:16 am Used commonly to replace the big nut, original from HK on. It is fouling because it is a modification to the original single circuit master. Moving it over slightly shouldn’t cause binding of the pedal and Clovis mechanism. This is a common modification. I haven’t done it myself but plenty have, and I’m pretty sure they didn’t need to go replacing bonnet springs melly.
Righto now it makes sense Clay, thanks... needed to do a bit of research with dr google - reckon you're right there should be enough to play within the setup if i open up a couple of holes here n there! cheers fellas
FB ute fixer upper, EK van on rotisserie
Melly's EK wag find
Re: Melly's EK wag find
Re: Melly's EK wag find
And so after another blunder highlighting my social media ineptness (I really should be getting my kids to do this shit), its back to posting this stuff in the forum where it is supposed to be ( my apologies to all)....after finally securing the services of someone who can weld properly, we made a start on getting the webers to fit.
so hinge and gas strut mods now added to workscope and then after a long absence of the welder, he returned to close up (some of the holes) It was around this time that my old mate had to leave again- not before giving me a quick lesson on how to use the gasless MIG ive acquired- and handing over
Being in a tight spot with some complex shapes (and limited Sheetmetal tooling available), old mate came up with an ingenious solution... enter one quarter piece of a 2kg gas bottle
I know this mod wont impress everyone, but once tacked in a trial fit of the carbs had me grinning
until it was time to trial fit bonnet so hinge and gas strut mods now added to workscope and then after a long absence of the welder, he returned to close up (some of the holes) It was around this time that my old mate had to leave again- not before giving me a quick lesson on how to use the gasless MIG ive acquired- and handing over
Re: Melly's EK wag find
So from here
it was a few quick trial runs on some offcuts i had lying around, to putting my welding and fabricating skills to the test and so this is where im at. The car is around 95% complete (thanks again to EKmart as id never even be close without it). I need to find some wagon Sunvisor brackets and lower tailgate hinges (the ones we salvaged Blacky are pretty knackered, but will get us home. I will need to drill out and oversize one of the hinge pins cause its flogged out). I think ive got pretty much everything else sorted on mockup, so its off to the brake and exhaust place next week to fit flanges to the extractors and run the rest of the pipes, then make up and run some new brake lines to the booster which ive relocated under the guard. When thats done, a good mate has offered his hoist and workshop for a couple of weeks so we can get the wiring in.
Hopefully the next update will not be as far away as the last one was...
Have a good pre- Nats weekend everyone, cheers,,,
craig melly
it was a few quick trial runs on some offcuts i had lying around, to putting my welding and fabricating skills to the test and so this is where im at. The car is around 95% complete (thanks again to EKmart as id never even be close without it). I need to find some wagon Sunvisor brackets and lower tailgate hinges (the ones we salvaged Blacky are pretty knackered, but will get us home. I will need to drill out and oversize one of the hinge pins cause its flogged out). I think ive got pretty much everything else sorted on mockup, so its off to the brake and exhaust place next week to fit flanges to the extractors and run the rest of the pipes, then make up and run some new brake lines to the booster which ive relocated under the guard. When thats done, a good mate has offered his hoist and workshop for a couple of weeks so we can get the wiring in.
Hopefully the next update will not be as far away as the last one was...
Have a good pre- Nats weekend everyone, cheers,,,
craig melly
Re: Melly's EK wag find
Great progress Craig.
Sent from my SM-G781B using Tapatalk
Sent from my SM-G781B using Tapatalk
getting my FB ute on the road
EK van on rotisserie
EK van on rotisserie
Re: Melly's EK wag find
If those hinges are no good mate we can grab the ones off the other wagon ????
I started with nothing and still have most of it left.
Foundation member #61 of FB/EK Holden club of W.A.
Foundation member #61 of FB/EK Holden club of W.A.
Re: Melly's EK wag find
Hi Melly if your standard modified hinges are too big maybe have a look at V6 Conversion hinges mate
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
The Reverend FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
Frankenstein EK V6 Ute
The Reverend FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
Re: Melly's EK wag find
If EKMart is out of stock of wagon lower tailgate hinges, give me a yell. I've probably got a set here somewhere.
Cheers,
Harv
Cheers,
Harv
327 Chev EK wagon, original EK ute for Number 1 Daughter, an FB sedan meth monster project and a BB/MD grey motored FED.
Re: Melly's EK wag find
Pretty sure I have some here in Perth Melly if you need
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
The Reverend FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
Frankenstein EK V6 Ute
The Reverend FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
Re: Melly's EK wag find
Thanks fellas, feel like I’m actually getting some forward traction again- I’ll bring the hinges with me to be assessed by the team when next we catch up… batten down the hatches guys the rains are comin