Harv's (Grace's) EK ute

Post photos of your pride and joy, or updates on your rebuild!

Moderators: reidy, Blacky

User avatar
Errol62
Posts: 10270
Joined: Sat Dec 06, 2014 2:44 pm
State: SA
Location: Adelaide

Re: Harv's (Grace's) EK ute

Post by Errol62 »

Grey motor cha cha, 1 2 - 1 2 3


FB ute fixer upper, EK van on rotisserie
getting my FB ute on the road
EK van on rotisserie
ardiesse
Posts: 1103
Joined: Thu Jan 19, 2017 9:57 am
State: NSW
Location: Sydney

Re: Harv's (Grace's) EK ute

Post by ardiesse »

The John Deere dealer at Cummins, SA, showed me how to get the clearance on a grey camshaft thrust washer right -

1. Press the gear onto the camshaft.
2. With an assistant holding the timing gear, deliver a calibrated blow to the camshaft hub with a hammer and soft metal drift.

It worked like magic.

Rob
User avatar
Harv
Posts: 5229
Joined: Mon Oct 08, 2007 2:00 pm
State: NSW
Location: Sydney, Australia

Re: Harv's (Grace's) EK ute

Post by Harv »

I watched a tradesman at Carb Service Co in Burwood use a similar technique to belt a drive plug into a Strommie. Drove it home perfectly, no damage. No way I would have smacked a carb that hard.

Cheers,
Harv
327 Chev EK wagon, original EK ute for Number 1 Daughter, an FB sedan meth monster project and a BB/MD grey motored FED.
User avatar
Harv
Posts: 5229
Joined: Mon Oct 08, 2007 2:00 pm
State: NSW
Location: Sydney, Australia

Re: Harv's (Grace's) EK ute

Post by Harv »

Timing cover, balancer, fan.

Strip bolt out in fan. I didn’t even lean on it. Retap water pump flange, find new bolt, grimace and assemble.

New (smaller) o-ring on dizzy, dizzy in. Much easier. Set rockers cold. Rocker cover. Radiator. Add cooooilant.

Bump coolant bottle off 2 stacked milk crates. 20 year old plastic bottle shatters, spraying coooolant over me and what looks like half the shed. Swear. Clean up green mess.

Turn engine by hand looking for mistakes. Leak from fuel pump shotglass… cork did not like being dry. Realise Rares don’t make the cork rings anymore. Do the arts-and-crafts thing and cut one from cork sheet.

Notice temp sender wire has end snapped off. Reterminate.

Go-no go for launch. Crank, crank, crank…. no noise.

Check for fuel (yessir!), check for spark (aye captain!). Must be timing, Dizzy out, advance on tooth.

Forget to turn ignition off, dizzy half out and cap clips arc out. Dance the hokey-pokey whilst juggling the sparking dizzy. Turn ignition off, curse own stupidity, put dizzy back in.

Notice that the temp sender wire did not like the hokey-pokey, and snapped again. Reterminate for the second time.

Time for second launch. Sounds better, almost catching. Run battery near dead, charge overnight.

Realise dizzy had been set for a slipped timing gear. Slack timing clamp, rotate dizzy body with ohmmeter checking for when points open. Ahhhhh… dizzy now much further clockwise, vac advance no longer pointing at side plate. Much better-er.

Third times the charm. Safety’s off, live fire on the range. Crank, crank, fire a few times, stop, Flames out the carb (new cam has overlap), eyebrows singed. Grin and go again. Fires, runs for ten seconds, stops. Lumpy. Grin.

Notice weep from where I disturbed thermostat cover. Rejoint, clean up spilt coooolant. Run out of time… it’s cold, and there are wolves out there.

More playing through the week.

Cheers,
Harv

Notice c
327 Chev EK wagon, original EK ute for Number 1 Daughter, an FB sedan meth monster project and a BB/MD grey motored FED.
User avatar
Brett027
Posts: 2366
Joined: Thu Apr 18, 2019 4:14 am
State: NSW

Re: Harv's (Grace's) EK ute

Post by Brett027 »

Geez Harv, remind me not to be anywhere near you when you are working on spark🤣.
Sucker for a rusty bomb
User avatar
Errol62
Posts: 10270
Joined: Sat Dec 06, 2014 2:44 pm
State: SA
Location: Adelaide

Re: Harv's (Grace's) EK ute

Post by Errol62 »

Keep us posted mate


FB ute fixer upper, EK van on rotisserie
getting my FB ute on the road
EK van on rotisserie
Blacky
Posts: 12800
Joined: Tue Jul 20, 2004 8:58 am
State: WA
Location: up in the Perth hills

Re: Harv's (Grace's) EK ute

Post by Blacky »

I'm glad I am not the only one who has these trials and tribulations ...... :thumbsup:
I started with nothing and still have most of it left.


Foundation member #61 of FB/EK Holden club of W.A.
User avatar
FJWALLY
Posts: 1833
Joined: Wed Nov 11, 2015 4:54 pm
State: VIC
Location: Forest Hill

Re: Harv's (Grace's) EK ute

Post by FJWALLY »

Lucky it wasn't a Maggie
Harv wrote: Sun Jul 04, 2021 5:40 pm Timing cover, balancer, fan.

Strip bolt out in fan. I didn’t even lean on it. Retap water pump flange, find new bolt, grimace and assemble.

New (smaller) o-ring on dizzy, dizzy in. Much easier. Set rockers cold. Rocker cover. Radiator. Add cooooilant.

Bump coolant bottle off 2 stacked milk crates. 20 year old plastic bottle shatters, spraying coooolant over me and what looks like half the shed. Swear. Clean up green mess.

Turn engine by hand looking for mistakes. Leak from fuel pump shotglass… cork did not like being dry. Realise Rares don’t make the cork rings anymore. Do the arts-and-crafts thing and cut one from cork sheet.

Notice temp sender wire has end snapped off. Reterminate.

Go-no go for launch. Crank, crank, crank…. no noise.

Check for fuel (yessir!), check for spark (aye captain!). Must be timing, Dizzy out, advance on tooth.

Forget to turn ignition off, dizzy half out and cap clips arc out. Dance the hokey-pokey whilst juggling the sparking dizzy. Turn ignition off, curse own stupidity, put dizzy back in.

Notice that the temp sender wire did not like the hokey-pokey, and snapped again. Reterminate for the second time.

Time for second launch. Sounds better, almost catching. Run battery near dead, charge overnight.

Realise dizzy had been set for a slipped timing gear. Slack timing clamp, rotate dizzy body with ohmmeter checking for when points open. Ahhhhh… dizzy now much further clockwise, vac advance no longer pointing at side plate. Much better-er.

Third times the charm. Safety’s off, live fire on the range. Crank, crank, fire a few times, stop, Flames out the carb (new cam has overlap), eyebrows singed. Grin and go again. Fires, runs for ten seconds, stops. Lumpy. Grin.

Notice weep from where I disturbed thermostat cover. Rejoint, clean up spilt coooolant. Run out of time… it’s cold, and there are wolves out there.

More playing through the week.

Cheers,
Harv

Notice c
You will find me lost somewhere!
User avatar
funkyscooter
Posts: 577
Joined: Wed Aug 16, 2017 8:12 am
State: NSW
Location: Sydney

Re: Harv's (Grace's) EK ute

Post by funkyscooter »

Nice update Harv, that gave me a giggle. Its all the little failures and complications that make the end result that much sweeter.
Scott
(Not so rusty) Ol' Rusty - FB/EK Sedan
User avatar
Harv
Posts: 5229
Joined: Mon Oct 08, 2007 2:00 pm
State: NSW
Location: Sydney, Australia

Re: Harv's (Grace's) EK ute

Post by Harv »

Brett027 wrote: Sun Jul 04, 2021 5:48 pm Geez Harv, remind me not to be anywhere near you when you are working on spark🤣.
You should see me install seatbelts. Two of the four kids refuse to EVER help me put seatbelts in again.

Cheers,
Harv
327 Chev EK wagon, original EK ute for Number 1 Daughter, an FB sedan meth monster project and a BB/MD grey motored FED.
User avatar
Brett027
Posts: 2366
Joined: Thu Apr 18, 2019 4:14 am
State: NSW

Re: Harv's (Grace's) EK ute

Post by Brett027 »

You might want to put out a book recounting the many exciting phases of you car history Harv 😀. I would put my hand up for a copy. Sometimes I wonder how you have survived, what with magic smoke and sparky things going off in all directions. A photo of the highly populated naughty corner sounds like it would be entertaining too. 🤗
Thanks for the posts, they are fantastic.
Sucker for a rusty bomb
User avatar
Harv
Posts: 5229
Joined: Mon Oct 08, 2007 2:00 pm
State: NSW
Location: Sydney, Australia

Re: Harv's (Grace's) EK ute

Post by Harv »

Fitted the Nasco bonnet holder, checked oil and water again. No stray tools under bonnet.

Two pumps on the go pedal, choke out half-inch, one third throttle and lit the wick. Fired up beautifully, but was not going to idle at the factory rpm :mrgreen:

Ran the cam in for twenty minutes. No leaks, nothing caught fire. Little rattly in the rockers.

Cooled it down, reset valve lash. A few were loose on the feeler. Reset the idle. Tidied up the few odds and ends.

Runs nice, no more excessively tappity tappits. Sounds good up through the rev range.

Needs a road test, but there is a red wagon with a blown diff blocking it in. Oh Steve, could you move the Camira? I need to get the Torana out so I can get to the Commodore. I’ll have to get the keys to the Cortina if I’m gonna move that Camira. Yeah. Watch the boat, mate. 🙄

Cheers,
Harv
327 Chev EK wagon, original EK ute for Number 1 Daughter, an FB sedan meth monster project and a BB/MD grey motored FED.
User avatar
Errol62
Posts: 10270
Joined: Sat Dec 06, 2014 2:44 pm
State: SA
Location: Adelaide

Re: Harv's (Grace's) EK ute

Post by Errol62 »

Result


FB ute fixer upper, EK van on rotisserie
getting my FB ute on the road
EK van on rotisserie
User avatar
Brett027
Posts: 2366
Joined: Thu Apr 18, 2019 4:14 am
State: NSW

Re: Harv's (Grace's) EK ute

Post by Brett027 »

Good going Harv. Grace will be chuffed. You seem to have a car or two in the drive.😆
Sucker for a rusty bomb
User avatar
mph
Posts: 787
Joined: Fri Oct 19, 2012 12:09 am
State: WA
Location: Perth's North

Re: Harv's (Grace's) EK ute

Post by mph »

Geez mate bet your glad to have a nice noise come out of that motor for a change.

Sent from my SM-G970F using Tapatalk

FB-Special
Big block 161 :lol:
Holley sniper EFI.
Vintage air ducted heat and cool.
Ek auto column shift.
Lj diff and reverse lights.
WA FB~EK Car Club Member.
Post Reply