Rebuilding of Old Timer (EK wagon)

Post photos of your pride and joy, or updates on your rebuild!

Moderators: reidy, Blacky

User avatar
Sputzwagon
Posts: 2708
Joined: Fri Dec 07, 2007 6:27 pm
State: NOT ENTERED
Location: Termeil, South Coast NSW

Post by Sputzwagon »

She's coming along there Stuart :D ..Give's you a warm 'n' fuzzy feeling when you get rid of the rust monster and start adding real steel again.
8)

Scotty.
[img]http://i249.photobucket.com/albums/gg211/scottyharrod/WOOFTOsmall.jpg[/img]
Woofto Car Club Member No 2
parisian62
Posts: 3996
Joined: Wed May 11, 2005 2:19 pm
State: NSW
Location: Sydney
Contact:

Post by parisian62 »

for sure Jay...with a couple of surfboards hanging out the back... :)

lots of warm n fuzzys happening Scotty!...my other half recently ventured out to the garage and said it was actually starting to look like a car again... :o :D
Feelin free in a '61 FB.
Member of FB-EK Holden Car Club Of NSW Inc.
Check out the Rebuild of Old Timer
caz
Posts: 34
Joined: Tue Aug 08, 2006 10:12 pm
State: NOT ENTERED
Location: Ballina

Re: Rebuilding of Old Timer (EK wagon) (Updated 17/3/10)

Post by caz »

When my car is complete and I go for a drive over the same Ballina Ferry, I'll think of this beauty...great story!
Yes! My Dream begins!
parisian62
Posts: 3996
Joined: Wed May 11, 2005 2:19 pm
State: NSW
Location: Sydney
Contact:

Re: Rebuilding of Old Timer (EK wagon) (Updated 17/3/10)

Post by parisian62 »

Good stuff Caz. Next time I'm up your way next year I might try and catch up with you...
Feelin free in a '61 FB.
Member of FB-EK Holden Car Club Of NSW Inc.
Check out the Rebuild of Old Timer
ekute62
Posts: 122
Joined: Sat Nov 14, 2009 12:57 pm
State: NOT ENTERED
Location: logan central

Re: Rebuilding of Old Timer (EK wagon) (Updated 17/3/10)

Post by ekute62 »

She's lookin good, well done mate...... :shock: :P
parisian62
Posts: 3996
Joined: Wed May 11, 2005 2:19 pm
State: NSW
Location: Sydney
Contact:

Re: Rebuilding of Old Timer (EK wagon) (Updated 17/3/10)

Post by parisian62 »

Many thanks ekute62,

Update time for March to May 2010...it's getting dark earlier with the end of daylight savings but the garage light is usually on...

Image

next area is the petrol tank 'well' which looked as though it has had a fair amount of water sitting in it over the years...

Image

cutting out...

Image

Image

this piece came via ratbox about 3 years ago and has been sitting in the garage ready for the transplant...

Image

Luis tacking it in...

Image

all in and some grinding to be done... :roll:

Image

an extra little section to the jigsaw from Greg (EK283)...

Image

Image
Feelin free in a '61 FB.
Member of FB-EK Holden Car Club Of NSW Inc.
Check out the Rebuild of Old Timer
parisian62
Posts: 3996
Joined: Wed May 11, 2005 2:19 pm
State: NSW
Location: Sydney
Contact:

Re: Rebuilding of Old Timer (EK wagon) (Updated 17/3/10)

Post by parisian62 »

next bits...

I wish the welding and grinding was as quick as posting stuff on the forum...

Image

Image

Image

other side...

Image

I love using this reciprocating saw...good for tight spots and neat corners...

Image

Image

and you guessed it more grinding... :evil:
Feelin free in a '61 FB.
Member of FB-EK Holden Car Club Of NSW Inc.
Check out the Rebuild of Old Timer
mrs ratbox

Re: Rebuilding of Old Timer (EK wagon) (Updated 17/3/10)

Post by mrs ratbox »

:) glad you could use it was a bit ordinary but i spose you can't just go buy one so anything is better than nothing :)
parisian62
Posts: 3996
Joined: Wed May 11, 2005 2:19 pm
State: NSW
Location: Sydney
Contact:

Re: Rebuilding of Old Timer (EK wagon) (Updated 25/5/10)

Post by parisian62 »

they were out of that section at Kmart... :wink: seriously after it was sand blasted, the edges cleaned up and some small patches which I didnt post up it was good as new... 8)
Feelin free in a '61 FB.
Member of FB-EK Holden Car Club Of NSW Inc.
Check out the Rebuild of Old Timer
Trev
Posts: 7897
Joined: Thu Apr 15, 2004 6:43 pm
State: NOT ENTERED
Location: Wonthaggi

Re: Rebuilding of Old Timer (EK wagon) (Updated 25/5/10)

Post by Trev »

Coming along nicely stewart, I bet luis is having a ball, all he has to do is weld the pieces in and they get magically ground down nice and flush :lol: , Trev 8) .
[img]http://i47.photobucket.com/albums/f177/trevwood/WOOFTOsmall.jpg[/img]
Woofto Car Club Member No3
User avatar
Devilrod
Posts: 7394
Joined: Fri Apr 30, 2004 12:55 pm
State: VIC
Location: Beaconsfield, Vic

Re: Rebuilding of Old Timer (EK wagon) (Updated 25/5/10)

Post by Devilrod »

Great work guys! Looking good, I'd be more than happy with that.
Speed and Style........... One day I'll get the speed bit.
customfc
Posts: 82
Joined: Fri Jun 03, 2005 11:05 pm
State: NOT ENTERED
Location: Sydney

Re: Rebuilding of Old Timer (EK wagon) (Updated 25/5/10)

Post by customfc »

Some nice progress.
I think I can see the light from here.
Regards
Alex
User avatar
rustysdungers
Posts: 439
Joined: Sun May 17, 2009 7:32 pm
State: NOT ENTERED

Re: Rebuilding of Old Timer (EK wagon) (Updated 25/5/10)

Post by rustysdungers »

HI stew a little birdy told me you are looking for some one too paint the old
girl talk to me at the nats about it :) :)
Where were you in '62???
User avatar
Stygian
Posts: 1274
Joined: Fri Sep 18, 2009 3:52 pm
State: NSW
Location: Upper North Shore, Sydney

Re: Rebuilding of Old Timer (EK wagon) (Updated 25/5/10)

Post by Stygian »

I always enjoy seeing updates of Old Timer, Stewart. Very impressed with the way you and Louie are repairing that bodyshell - very precise and clean. Great stuff!

So, are those Tasmans that I KNOW you scored going on? :wink: :)

Andrew
parisian62
Posts: 3996
Joined: Wed May 11, 2005 2:19 pm
State: NSW
Location: Sydney
Contact:

Re: Rebuilding of Old Timer (EK wagon) (Updated 25/5/10)

Post by parisian62 »

thanks everyone for their comments.

I wish it was magic Trev.

Yep VERY happy DR...a dream come true.

You're on the money Alex definitely on the downhill run...I don't think Luis can believe it...nor can I for that matter...it's been a hard slog.

Thats little birdy is right Russell. C U at the nats.

Too right Andrew 8) Hopefully will pick them up at the Club meeting on Tuesday night :D 8)
Feelin free in a '61 FB.
Member of FB-EK Holden Car Club Of NSW Inc.
Check out the Rebuild of Old Timer
Post Reply