hey guys,
i need my bumpers/dash/lights surrounds done...
has anyone had theirs done recently...
i'm wanting to know the following...
where...
how much...
was it a good job...
thanks
matty martin
GOOD, chroming in NSW
-
mattymartin
- Posts: 841
- Joined: Fri Oct 06, 2006 12:49 pm
- State: NOT ENTERED
- Location: sydney
GOOD, chroming in NSW
go the wagons....
-
parisian62
- Posts: 3997
- Joined: Wed May 11, 2005 2:19 pm
- State: NSW
- Location: Sydney
- Contact:
Hi Matty,
Hope you've got plenty of $$$ in that wallet of yours...here's some info on places I know and have used...
Blu Chrome at Milperra...have had chrome and zinc plating done there and was happy with the results...they wont do cast stuff like blinker surrounds, bonnet bar and tailights...
All Metal Bumpers at Ingleburn...have had chrome done there...they will do cast...I think it is sent to the chrome place at Melbourne...can't remember the name...
Astor Metal Finishes at Villawood...have had polishing work done there...they also do chroming and will do albeit reluctantly cast stuff...
Electroplating Technology at Qeanbeyan...have read they do a lot of stuff for hot rodders...have never used them...only because of their location...
all the contact details can be found at
http://www.fbekholden.com/forum/viewtop ... =1771#1771
price wise you are looking at approx $150 per section for a bumper bar...
regards
Stewart
ps I moved your post into the right Forum category.
Hope you've got plenty of $$$ in that wallet of yours...here's some info on places I know and have used...
Blu Chrome at Milperra...have had chrome and zinc plating done there and was happy with the results...they wont do cast stuff like blinker surrounds, bonnet bar and tailights...
All Metal Bumpers at Ingleburn...have had chrome done there...they will do cast...I think it is sent to the chrome place at Melbourne...can't remember the name...
Astor Metal Finishes at Villawood...have had polishing work done there...they also do chroming and will do albeit reluctantly cast stuff...
Electroplating Technology at Qeanbeyan...have read they do a lot of stuff for hot rodders...have never used them...only because of their location...
all the contact details can be found at
http://www.fbekholden.com/forum/viewtop ... =1771#1771
price wise you are looking at approx $150 per section for a bumper bar...
regards
Stewart
ps I moved your post into the right Forum category.
Feelin free in a '61 FB.
Member of FB-EK Holden Car Club Of NSW Inc.
Check out the Rebuild of Old Timer
Member of FB-EK Holden Car Club Of NSW Inc.
Check out the Rebuild of Old Timer
-
mattymartin
- Posts: 841
- Joined: Fri Oct 06, 2006 12:49 pm
- State: NOT ENTERED
- Location: sydney
thanks stewart,
All Metal Bumpers at Ingleburn...have had chrome done there...they will do cast...I think it is sent to the chrome place at Melbourne...can't remember the name...
this is the place i was going to go with... i also think you info is correct re, cast stuff being sent to melb...
i spoke to peter there yesterday & he was very helpful & nice on the phone, he quoted me 150 per section....
alan from alan mccoy, (the guy that did my stainless mouldings) put me on to them he also said that they are the only ones he would reccommend besides the Electroplating Technology at Qeanbeyan...
thanks
matty martin
All Metal Bumpers at Ingleburn...have had chrome done there...they will do cast...I think it is sent to the chrome place at Melbourne...can't remember the name...
this is the place i was going to go with... i also think you info is correct re, cast stuff being sent to melb...
i spoke to peter there yesterday & he was very helpful & nice on the phone, he quoted me 150 per section....
alan from alan mccoy, (the guy that did my stainless mouldings) put me on to them he also said that they are the only ones he would reccommend besides the Electroplating Technology at Qeanbeyan...
thanks
matty martin
go the wagons....