Page 1 of 1

FB boot seal

Posted: Fri Mar 02, 2018 3:58 pm
by 59wagon
Hi All, my boot seal is pretty much cactus. I can get one from Rares - anyone know if they fit ok?
Also, what’s the best goo to use to stick it in place?
It looks like the old one will come out pretty easy using a flat blade screwdriver.
The job looks pretty straight forward - any tips would be appreciated.
Cheers,
John


Sent from my iPhone using Tapatalk

Re: FB boot seal

Posted: Fri Mar 02, 2018 4:00 pm
by 59wagon
Here’s a picture
Image


Sent from my iPhone using Tapatalk

Re: FB boot seal

Posted: Fri Mar 02, 2018 6:21 pm
by CHOPPED
sika flex is best by far
let me know if you need some mate

Re: FB boot seal

Posted: Fri Mar 02, 2018 6:38 pm
by EK283
Poke with caution John,

The dreaded rust normally lurks behind !!

Regards Greg

Re: FB boot seal

Posted: Fri Mar 02, 2018 6:50 pm
by 59wagon
CHOPPED wrote: Fri Mar 02, 2018 6:21 pm sika flex is best by far
let me know if you need some mate
Thanks Paul, see you at the meeting tonight?

"Poke with caution John,

The dreaded rust normally lurks behind !!

Regards Greg"

Good tip, thanks Greg. There's a few dings and dents I'll have to fix as well, the metal looks pretty thin around this area.

Re: FB boot seal

Posted: Sat Mar 03, 2018 12:00 am
by Errol62
Contact same as what Harv is using for head lining. They can be very tight like doors and sometimes the outer edge will pop out of the gap between body and lid. Pretty hard to get right at the top corners where water can pool and leak in.
Good luck


Sent from my iPad using Tapatalk

Re: FB boot seal

Posted: Sat Mar 03, 2018 7:15 am
by Harv
I've used contact cement (Kwikgrip, gorilla snot) on the boot rubber with mixed success. Because it flexes frequently, the glue tends to come away. Sikaflex is a bit more long lasting.

Don't forget that the orientation of the rubber is important - the lip should point inwards towards the centre of the boot, not outwards.

Cheers,
Harv

Re: FB boot seal

Posted: Sat Mar 03, 2018 5:38 pm
by 59wagon
Harv wrote: Sat Mar 03, 2018 7:15 am I've used contact cement (Kwikgrip, gorilla snot) on the boot rubber with mixed success. Because it flexes frequently, the glue tends to come away. Sikaflex is a bit more long lasting.

Don't forget that the orientation of the rubber is important - the lip should point inwards towards the centre of the boot, not outwards.

Cheers,
Harv
Thanks, Harv. Which Sikaflex product? Here's the list from the big green shed:

https://www.bunnings.com.au/search/prod ... ctFrom=Any

In the picture below, you're saying the right hand side points towards the centre of the boot?

https://www.rarespares.net.au/welshpool ... ct=RBS1002

Cheers,

John

Re: FB boot seal

Posted: Sun Mar 04, 2018 7:11 am
by Harv
59wagon wrote: Sat Mar 03, 2018 5:38 pmThanks, Harv. Which Sikaflex product? Here's the list from the big green shed:
https://www.bunnings.com.au/search/prod ... ctFrom=Any
I tend to use Sikaflex 257 or 252 from SuperCheap - more adhesive than a sealant.
59wagon wrote: Sat Mar 03, 2018 5:38 pm In the picture below, you're saying the right hand side points towards the centre of the boot?
https://www.rarespares.net.au/welshpool ... ct=RBS1002
Yep 8)

Cheers,
Harv

Re: FB boot seal

Posted: Sun Mar 04, 2018 10:04 am
by 59wagon
:thumbsup: Thanks Harv