Page 16 of 47
Re: LS1EK
Posted: Thu Jun 13, 2019 11:23 pm
by TAZ
Gave a pipe a bit of a clean up. Came very nice and should look grouse once ceramic coated.
I also finally got the airconditioner condenser required to fit behind the grill and under the bonnet catch bar.
I was stuck for height but sourced this one which is only 160mm high but 60mm thick. It will fit perfect.
Sent from my SM-J730G using Tapatalk
Re: LS1EK
Posted: Sun Jun 16, 2019 12:39 am
by TAZ
Pipes are all done. I will need to cut some more steel out on the drivers side to clear the two rear pips.
Sent from my SM-J730G using Tapatalk
Re: LS1EK
Posted: Sun Jun 16, 2019 7:21 am
by EK283
Nice work Taz,
They take a lot of time to build but well worth it in the end. Ceramic coating will keep the temperature down a lot as well.
regards Greg
Re: LS1EK
Posted: Sun Jun 16, 2019 8:18 am
by Errol62
Great work Taz. Keep at it mate.
Sent from my iPhone using Tapatalk
Re: LS1EK
Posted: Sun Jun 16, 2019 8:22 am
by FireKraka
Nice Taz you have a lot more patience than I do and they certainly will look good when they are ceramic coated mate.
Neil
Re: LS1EK
Posted: Sun Jun 16, 2019 8:05 pm
by TAZ
Took the old girl out for some vitamin C
Sent from my SM-J730G using Tapatalk
Re: LS1EK
Posted: Mon Jun 17, 2019 12:24 pm
by TAZ
TAZ wrote: Sun Jun 16, 2019 8:05 pm
Took the old girl out for some vitamin D
Sent from my SM-J730G using Tapatalk
Re: LS1EK
Posted: Fri Jun 28, 2019 5:06 pm
by TAZ
Wipe motor finally mounted. Engine, gearbox and front suspension are out. Time to finally finish off the engine bay and fire wall.
Sent from my SM-J730G using Tapatalk
Re: LS1EK
Posted: Fri Jun 28, 2019 9:38 pm
by Blacky
love your work mate - be good to see this beast on the road
Re: LS1EK
Posted: Sat Jun 29, 2019 12:50 am
by TAZ
Fire wall almost finished. Drivers side chassis rail done.
Sent from my SM-J730G using Tapatalk
Re: LS1EK
Posted: Sat Jun 29, 2019 12:55 am
by Errol62
Neat job on the front rail Taz.
FB ute fixer upper, EK van on rotisserie
Re: LS1EK
Posted: Sat Jun 29, 2019 7:25 am
by TAZ
Errol62 wrote:Neat job on the front rail Taz.
FB ute fixer upper, EK van on rotisserie
Cheers mate. Getting there slowly.
Sent from my SM-J730G using Tapatalk
Re: LS1EK
Posted: Sat Jun 29, 2019 7:26 am
by TAZ
Blacky wrote:love your work mate - be good to see this beast on the road
You and me both Blacky. Money is the big handbrake at the moment
Sent from my SM-J730G using Tapatalk
Re: LS1EK
Posted: Mon Jul 01, 2019 10:40 pm
by TAZ
CHOPPED wrote: Sat Sep 02, 2017 12:51 am
mate it took me 2 weeks to do mine
alot more than it looks
Hey ya Chopped, just wondering did you reinforce the support on the inside where you scolloped it out to allow the exhaust pipes to pass?.
Re: LS1EK
Posted: Thu Jul 04, 2019 2:10 pm
by CHOPPED
hey man sorry mate
just seen this pm
yes i put a piece of 200 dia by 10 mm scallop in there and welded it in
engineer looked at itwhile still in its metal stage and just laughed and said
fark overkill
carry on man
looking good
Paul
