Re: My EK project
Posted: Sat Dec 20, 2014 8:08 am
Looking good! 
Page 91 of 105
Re: My EK project
Posted: Sat Dec 20, 2014 9:49 am
Drunk xmas day burnouts in the shed?
Re: My EK project
Posted: Sat Dec 20, 2014 2:11 pm
Shit hot Jase !!!
Re: My EK project
Posted: Tue Dec 23, 2014 7:47 pm
burnouts in the shed,now theirs a story I have to tell
my old man was a bit of a grease monkey,working on his MS85 crown and all...
I got a hj sedan gts from a dodgy caryard here in bris,it could keep up/slighty faster with a newish walknishaw
at the time,anyways I used my dads shed to give all my cars resprays
to cut a long story short he wasn't due home for hours
so I dropped a tyre popping skid,giggling coughing,giggling
couldn't see much ,nearly as good if not better than shit you pay to see
my old man was only mad at me once
that was the time
he could see smoke rising from his beloved shed from a mile away
he pulled in the driveway in his 76 crown,"curnal mustard"we called it
"your not going to work on your car anymore today" he said
such a good skid though the wind/breeze always settles at the worst of times.
I haven't fired the 186 up yet but im quietly confident it will pop a skid
maybe a race ,an old school race ...maybe not cause id get tasered
and I don't even have a rego sticker cause there gone...crazy days
my old man was a bit of a grease monkey,working on his MS85 crown and all...
I got a hj sedan gts from a dodgy caryard here in bris,it could keep up/slighty faster with a newish walknishaw
at the time,anyways I used my dads shed to give all my cars resprays
to cut a long story short he wasn't due home for hours
so I dropped a tyre popping skid,giggling coughing,giggling
couldn't see much ,nearly as good if not better than shit you pay to see
my old man was only mad at me once
that was the time
he could see smoke rising from his beloved shed from a mile away
he pulled in the driveway in his 76 crown,"curnal mustard"we called it
"your not going to work on your car anymore today" he said
such a good skid though the wind/breeze always settles at the worst of times.
I haven't fired the 186 up yet but im quietly confident it will pop a skid
maybe a race ,an old school race ...maybe not cause id get tasered
and I don't even have a rego sticker cause there gone...crazy days
Re: My EK project
Posted: Tue Dec 23, 2014 8:40 pm
cheap door rubbers need a SLAM 90 bucks for 30m
inners and outers with loving lol
160 bucks .,no quarter rubbers
inners and outers with loving lol
160 bucks .,no quarter rubbers
Re: My EK project
Posted: Fri Dec 26, 2014 9:17 pm
I made a quarter glass seal today,i think it will seal,
I cannot afford proper seals ?
60 bucks a side ,just for the tiny windows ..I could not spend that much so I made my own
only one mistake ..,,.
my doors are closing really nice after spending a week closed
and the shit the glass goes up and down in is great
easy to wind up or down
im rustproofing and greasing as I go with lanolin , being a sheep phucker and all
I cannot afford proper seals ?
60 bucks a side ,just for the tiny windows ..I could not spend that much so I made my own
only one mistake ..,,.
my doors are closing really nice after spending a week closed
and the shit the glass goes up and down in is great
easy to wind up or down
im rustproofing and greasing as I go with lanolin , being a sheep phucker and all
Re: My EK project
Posted: Fri Dec 26, 2014 9:23 pm
Cheap rubbers=good chit. 
Re: My EK project
Posted: Sun Dec 28, 2014 7:46 pm
Re: My EK project
Posted: Mon Dec 29, 2014 5:57 pm
Very nice Jas..
Re: My EK project
Posted: Mon Dec 29, 2014 7:39 pm
not far now 
tell us more about the rubbers and window chanelling you used what it is and where you got it thenks
tell us more about the rubbers and window chanelling you used what it is and where you got it thenks
Re: My EK project
Posted: Tue Dec 30, 2014 7:59 pm
hey mick ues Pritchard rd Virginia
lovely fellas
p 406, for the rubbers use good glue 424 loktite
flip the rubber for the quarter glass once all the old is removed
glue in as you go ,chop vees out for the pivot points
flat blunt screwdriver to push the rubber home
lots of glue and patience trim the bottom section with a new blade by 4.56mm,lol
lovely fellas
p 406, for the rubbers use good glue 424 loktite
flip the rubber for the quarter glass once all the old is removed
glue in as you go ,chop vees out for the pivot points
flat blunt screwdriver to push the rubber home
lots of glue and patience trim the bottom section with a new blade by 4.56mm,lol
Re: My EK project
Posted: Wed Dec 31, 2014 11:34 am
Re: My EK project
Posted: Wed Dec 31, 2014 7:08 pm
pulled down the orig door trims yesterday,wow I was going to use them as a pattern.....
but they are a lot better than what I recall
and its a budget build,they have lasted 50 years ,they must be ok..
will put a new back board on my door ,only because I have to
are the measurements up on this site for door backing cards?
the blue turns green over the years
but they are a lot better than what I recall
and its a budget build,they have lasted 50 years ,they must be ok..
will put a new back board on my door ,only because I have to
are the measurements up on this site for door backing cards?
the blue turns green over the years
Re: My EK project
Posted: Wed Dec 31, 2014 7:23 pm
Re: My EK project
Posted: Wed Jan 14, 2015 2:54 pm
Bout to fit front and rear screens
Any advice would be great,do I have to use the black gooey stuff?
Any advice would be great,do I have to use the black gooey stuff?