Project EK

Post photos of your pride and joy, or updates on your rebuild!

Moderators: reidy, Blacky

Post Reply
t950cat
Posts: 200
Joined: Mon Jun 25, 2007 7:21 pm
State: NOT ENTERED
Location: Horsley

Project EK

Post by t950cat »

Hi All
Well i think it is time to start as i have finally found a sandblaster to do the car (i am a tickler at doing my homework).I started this about 6 months ago and hope to complete it ????????????????????? i dont rush things ask the wife :lol: :lol: .I will keep you up to date with photos and we will see how it goes.
Cheers
TonyImage
Stand and listen to knowledge turn your back on stupidity.......
Top
karsten
Posts: 613
Joined: Wed Oct 17, 2007 6:31 am
State: NOT ENTERED
Location: bungendore nsw

Post by karsten »

thats a pretty good shell tony,,should be a good car whats the front frame like

i was glad i sand blasted so i new there was no rust hidding cleans it up good ,although you find any repairs to panels that you never would have found with out bare stripping,,,,,,just tell em to take time and wisk it bit at a time or they could warp ,,,even if its a couple hundred more ,,, take there time its saves alot of stripping
when they start building them like that again i will buy a new car of them
Top
t950cat
Posts: 200
Joined: Mon Jun 25, 2007 7:21 pm
State: NOT ENTERED
Location: Horsley

Post by t950cat »

hey Karsten
The shell has next to no rust in it just a small square on the drivers floor and a little bit round the rear window and what you see in the firewall mate.The subframe requires a little bit of work as i had to cut the battery box out and i am going to make a new one.Helps to have mate whose a boilermaker/fitter too.All the front suspension is now powder coated and all new rubbers etc will be going in.As for the sandblasting i did alot of research on it and found one not far from home who did my mates ss hatchback torana and did a great job.So here we go mate the beer fridge is full so starts the long journey as i said i dont rush things.
cheers
Tony
Stand and listen to knowledge turn your back on stupidity.......
Top
t950cat
Posts: 200
Joined: Mon Jun 25, 2007 7:21 pm
State: NOT ENTERED
Location: Horsley

Post by t950cat »

OH by the way the garage is alot cleaner now than in the picture.(i feel so ashamed to have treated my shed like that :( :( :( :(
Stand and listen to knowledge turn your back on stupidity.......
Top
Malcolm
Posts: 709
Joined: Tue May 23, 2006 8:20 am
State: NOT ENTERED
Location: Gympie

project ek

Post by Malcolm »

Hey Tony,

The body looks good, hopefully the blasting won't uncover to much more work for you. The body on mine looked pretty good until I had it blasted, ended up having to replace 4 floor pans and 1 outer sill. But I guess thats still good compared to what some have started with.

Make sure you keep us up to date with progress info and pickies.

Cheers
Malcolm W.
Top
User avatar
Thommo
Posts: 3687
Joined: Mon Feb 05, 2007 4:42 pm
State: NOT ENTERED
Location: Adelaide

Post by Thommo »

Nice one Tony 8)
Thanks for deciding to share your pics with us 8)
It looks to be in good shape from here.
Good luck with the project.
Do you have some pics of it before it came apart?
Cheers
Jeff
Top
parisian62
Posts: 3997
Joined: Wed May 11, 2005 2:19 pm
State: NSW
Location: Sydney
Contact:
Contact parisian62

Post by parisian62 »

Good stuff Tony. Its good to do you 'homework' as you say in your first post. I see from your avatar the EK still has original plates...have you still got both of them?

regards
Stewart
Feelin free in a '61 FB.
Member of FB-EK Holden Car Club Of NSW Inc.
Check out the Rebuild of Old Timer
Top
FB MAD
Posts: 2725
Joined: Thu Jun 30, 2005 7:59 pm
State: NOT ENTERED
Location: Upper Hunter N.S.W

Post by FB MAD »

Tony, don't feel bad about the mess in your shed...... I need a map to get out of mine!! :oops: :oops: :oops:
I can't think what to write here so this will do.
Top
t950cat
Posts: 200
Joined: Mon Jun 25, 2007 7:21 pm
State: NOT ENTERED
Location: Horsley

Post by t950cat »

Damn no i haven,t got the plates Stewart.i put them on hold in the rta and let the time limit run out so i thought i will have historic plates on it or my own plates not sure yet mate.Trust me this body is in great nick i was surprised when i stripped it guys its that good.I followed your build mal with much interest and have most of your pix saved on a file for reference(and inspiration)once again well done.Will try and find some photos Jeff but we had a pc crash and lost a bit so i will have to check.Once again i hope i do you proud as they are a great car with alot of style.
Cheers
Tony
Stand and listen to knowledge turn your back on stupidity.......
Top
t950cat
Posts: 200
Joined: Mon Jun 25, 2007 7:21 pm
State: NOT ENTERED
Location: Horsley

Post by t950cat »

Hi all
The blaster i found quoted 1300 to do the job and a mate told me to ring this bloke in wollongong and he came and looked at the car and quoted 2000 plus gst.He has a reputation of doing a great job but S&%# he charges like a wounded bull.Maybe i should have paint stripped the car to save the dollars.
Tony
Stand and listen to knowledge turn your back on stupidity.......
Top
t950cat
Posts: 200
Joined: Mon Jun 25, 2007 7:21 pm
State: NOT ENTERED
Location: Horsley

Post by t950cat »

What was your price karsten to do your car?????
Stand and listen to knowledge turn your back on stupidity.......
Top
TAYZ 58
Posts: 297
Joined: Mon Jun 20, 2005 7:14 pm
State: NOT ENTERED

Post by TAYZ 58 »

That sounds pretty dear but Im not sure on prices, different states. I just pulled a EJ ute to a shell and got it sandblasted right through, great job for $300- and in primer.
Top
t950cat
Posts: 200
Joined: Mon Jun 25, 2007 7:21 pm
State: NOT ENTERED
Location: Horsley

Post by t950cat »

Now thats a good price. i have never seen prices vary so much but hes goota no what hes doing.from memory i think Mals was about 500 so with my quotes they are sounding dear.
Tony
Stand and listen to knowledge turn your back on stupidity.......
Top
rosco
Posts: 2569
Joined: Wed Feb 04, 2004 8:34 pm
State: VIC
Location: Melbourne

Post by rosco »

Hi Tony,
I wish my garage looked as neat as your's - and I love your cradle for rolling the body around on....... very clever.....

Body looks in excellent shape - especially the sub-frame mount....... and sill mounts.......

Great to see another treasure getting proper respect........

please keep us up to date with your project and plenty of pix..

thanks for sharing,

frats,
Rosco
Top
t950cat
Posts: 200
Joined: Mon Jun 25, 2007 7:21 pm
State: NOT ENTERED
Location: Horsley

Post by t950cat »

Well all i know i said i was going to sandblast but when i heard the price i thought i can save a couple of $$$$$$$$$$ if i strip the flat panels(and safer too) so heres some updated photos of the roof.wOW what a mess stripper can make but i think of the $$$$$$$$.
Tony
Image
Image
Stand and listen to knowledge turn your back on stupidity.......
Top
Post Reply

Return to “My FB EK”