Valerie the EK Standard Sedan

gpi · Post by **gpi** » Sun Jan 07, 2018 3:32 pm

: IMG_0586.JPG (376 KiB) Viewed 2417 times

gpi · Post by **gpi** » Sun Jan 07, 2018 8:41 pm

Front wheels off for caliper overhaul.
Front end has UC/LX Torana disc conversion. The calipers are the alloy bodied ones with cast iron pad holders. Gave Val a quick wash too.

: IMG_0568.JPG (1.87 MiB) Viewed 2397 times

Sent from my iPhone using Tapatalk

Errol62 · Post by **Errol62** » Sun Jan 07, 2018 11:29 pm

Colleen Green? My favourite. She’s had a bit of a dress up with the stainless window and gutter trim, chrome light surrounds front and rear. Obviously had some attention over the years.
I take it the Torana discs are on a HR ball joint front end?

Sent from my iPad using Tapatalk

gpi · Post by **gpi** » Mon Jan 08, 2018 11:25 am

Valetta Green (0250)

Yes, HR front end w/ torana brakes,186, trimatic and hr diff

I have some front surrounds if stripped to paint as standard, however, i am on the hunt for some standard rear lights.

Errol62 · Post by **Errol62** » Mon Jan 08, 2018 1:30 pm

Valletta green. Thanks.
I have a pair of standard rear lights at Willunga, assuming by the plates you are in SA. Gratis to you if you don’t want to scuff the chrome off and paint the ones you have.
Cheers
Clay

Sent from my iPad using Tapatalk

gpi · Post by **gpi** » Tue Jan 09, 2018 7:14 pm

Unfortunately these are not HR Holden brakes...

: IMG_0588.JPG (410.34 KiB) Viewed 2326 times

gpi · Post by **gpi** » Tue Jan 09, 2018 7:24 pm

EK brakes. Largest pads at the front...

Errol62 · Post by **Errol62** » Tue Aug 07, 2018 6:45 pm

How is progress Patrick?

Sent from my iPad using Tapatalk

Errol62 · Post by **Errol62** » Tue Aug 07, 2018 6:48 pm

You’re going to have to change the rear axle to match front brakes. What have you got in mind? EJ-H, HD-R, LC-J?

Sent from my iPad using Tapatalk

gpi · Post by **gpi** » Wed Aug 08, 2018 9:14 am

Hi Clay and fellow FBEKers,
diff may stay as i have turned to the dark side and am reducing the cubes

brake setup has hj proportioning valve and vh24 with PBR alloy LX-UC calipers and discs

Errol62 · Post by **Errol62** » Wed Aug 08, 2018 9:33 am

Cool mate. An interesting combination there. VH24, that is Nasco issue EH era and factory HR disc? I wondered if they had fitted a proportioning valve. Another option is to go dual circuit and only boost the front I am told.

gpi · Post by **gpi** » Thu Aug 09, 2018 4:47 pm

i think i should take the hr diff out of the 225 and use that, but im not convinced the rims will fit back on without out issues...

Errol62 · Post by **Errol62** » Thu Aug 09, 2018 9:21 pm

I reckon that HR and EK are identical width

Sent from my iPhone using Tapatalk

gpi · Post by **gpi** » Thu Aug 09, 2018 9:47 pm

hmmm, if i keep the 225s on the back i guess ill have the standard issues...

59wagon · Post by **59wagon** » Fri Aug 10, 2018 2:38 am

I just had a look at the spec's. They vary a bit depending where you look, but it appears pretty consistent that FB to HD were the same, then HR was 10mm wider.

Cheers,

John

fbekholden.com