Wayne with a Sydney 1961 FB

Post photos of your pride and joy, or updates on your rebuild!

Moderators: reidy, Blacky

Mick
Posts: 4172
Joined: Sun Sep 26, 2010 8:47 am
State: NSW
Location: Coffs Harbour NSW

Re: Wayne with a Sydney 1961 FB

Post by Mick »

off the top of my head a redish brown and black and even in an EK is separate wiring from the harness and has it's own inline fuse
sometimes yor just better off shitting in yor hands and clapping

W.S.C.C.A
Woodstock chapter
User avatar
Craig Allardyce
Posts: 1464
Joined: Sun Aug 07, 2011 7:26 pm
State: VIC
Location: Stratford

Re: Wayne with a Sydney 1961 FB

Post by Craig Allardyce »

WayneXG95 wrote:Been in the Auto Electrican since last week and hope it will be ready by the end of next week :problem:
I found one that did his apprenticeship on FB and EK Holdens..GOLD! :thumbsup:

Image

Small problem, I gave him the FB manual so he had the electrical diagram to work off but forgot I have electric wipers
so tomorrow I have to take my EK one to him...bugger :lol:

Image

Image

Picked this up today from the local lifeline shop...will give the old girl the old man look...matches Milkshake prefectly :mrgreen:

Image

Getting there slowly :D
I expect that you'll be wearing the appropriate bowling on your first drive! :wtf: :wtf: :wtf:

Looking god mate!! :clap: :clap: :thumbsup: :thumbsup:
User avatar
WayneXG95
Posts: 2565
Joined: Wed Sep 07, 2011 9:42 am
State: NSW
Location: Sydney

Re: Wayne with a Sydney 1961 FB

Post by WayneXG95 »

So whats been happening.

Daniel from A Sitch In Time came around today and installed my roof lining...
We can install the front and rear windows tomorrow also with scuff plates and other stuff.
Monday booked to have the exchust installed and a blue slip...
If it passes it's off for a wheel alinement and hopefully Gray Pride the following Sunday..
'Fingers Crossed".....

Image

Image

Image

I chose plastic instead of board for the door cards. Never rot.

Image

Image

Image

Image

Image

Image

Image

Image

So until tomorrow kiddies.... :mrgreen:
Wayne Chambers
President
FB EK Holden Car Club of N.S.W
bootlegger
Posts: 2070
Joined: Sat Sep 26, 2009 7:52 pm
State: NOT ENTERED
Location: sydney

Re: Wayne with a Sydney 1961 FB

Post by bootlegger »

Awsome.
Mick Jagger
Posts: 3430
Joined: Mon Dec 08, 2008 12:48 pm
State: NOT ENTERED
Location: Brisbane

Re: Wayne with a Sydney 1961 FB

Post by Mick Jagger »

so that bar under the bonnet is meant to be bent
lovely resto
kmawic
User avatar
Sputzwagon
Posts: 2708
Joined: Fri Dec 07, 2007 6:27 pm
State: NOT ENTERED
Location: Termeil, South Coast NSW

Re: Wayne with a Sydney 1961 FB

Post by Sputzwagon »

Funny how Rusty does a great paint job on your car and leaves me to paint his???
Looking good Wayne. :thumbsup:

Scotty.
[img]http://i249.photobucket.com/albums/gg211/scottyharrod/WOOFTOsmall.jpg[/img]
Woofto Car Club Member No 2
User avatar
samprinci
Posts: 1111
Joined: Thu Aug 06, 2009 10:17 am
State: NOT ENTERED
Location: Nthrn Beaches / Liverpools - Syd

Re: Wayne with a Sydney 1961 FB

Post by samprinci »

Hey Wayne .. Lookin really good mate. Can't wait to see it in the flesh..
Quick question. How did u guys do the dealer name under bonnet ???
Join the fun! Join the club! - FB-EK Holden Car Club of NSW
www.fbekholdennsw.com
User avatar
Cal
Posts: 2796
Joined: Sat Nov 08, 2008 8:07 pm
State: NOT ENTERED
Location: Sydney

Re: Wayne with a Sydney 1961 FB

Post by Cal »

Looking good, Wayne. Credit to you and Russell
User avatar
WayneXG95
Posts: 2565
Joined: Wed Sep 07, 2011 9:42 am
State: NSW
Location: Sydney

Re: Wayne with a Sydney 1961 FB

Post by WayneXG95 »

samprinci wrote:Hey Wayne .. Lookin really good mate. Can't wait to see it in the flesh..
Quick question. How did u guys do the dealer name under bonnet ???
Any printer should be able to cut it Sam.... :shh:
Wayne Chambers
President
FB EK Holden Car Club of N.S.W
parisian62
Posts: 3996
Joined: Wed May 11, 2005 2:19 pm
State: NSW
Location: Sydney
Contact:

Re: Wayne with a Sydney 1961 FB

Post by parisian62 »

Go Wayne! On the downhill run now... :thumbsup:
Feelin free in a '61 FB.
Member of FB-EK Holden Car Club Of NSW Inc.
Check out the Rebuild of Old Timer
User avatar
WayneXG95
Posts: 2565
Joined: Wed Sep 07, 2011 9:42 am
State: NSW
Location: Sydney

Re: Wayne with a Sydney 1961 FB

Post by WayneXG95 »

Well it's all over red rover, we have plates!.... :D
No problems with the blue slip she went straight through... :thumbsup:

Image

Image

Image

Image

Image

Image

It's so good when the final pieces go on.
A big thanks to Russell (rustydungers) for all the work he did on Milkshake, The paint looks spick... :ewink:

I'll be taking her to the club meeting tonight and if all goes well and no problems with the wheel alinement on wednesday
she will be a Berrima "Gray Pride" on Sunday 8)
Wayne Chambers
President
FB EK Holden Car Club of N.S.W
User avatar
Cal
Posts: 2796
Joined: Sat Nov 08, 2008 8:07 pm
State: NOT ENTERED
Location: Sydney

Re: Wayne with a Sydney 1961 FB

Post by Cal »

Good stuff :clap: :clap:

What's with the XTN plates?


And for fecks sake put the plates on properly :lol:
User avatar
John
Posts: 719
Joined: Sun May 17, 2009 7:28 pm
State: NOT ENTERED
Location: Ulverstone Tasmania

Re: Wayne with a Sydney 1961 FB

Post by John »

Congrats mate! Looks awesome!
Isn't it a shit hot feeling bolting those plates on. :thumbsup: :thumbsup: :thumbsup: :thumbsup: :thumbsup:
Not all chemicals are bad. Without chemicals such as hydrogen and
oxygen, for example, there would be no way to make water, a vital
ingredient in beer
searsy
Posts: 629
Joined: Sun Jun 26, 2011 2:45 pm
State: NOT ENTERED
Location: Lismore NSW

Re: Wayne with a Sydney 1961 FB

Post by searsy »

Just perfect
I have enjoyed watching this build
Now get out there and enjoy
User avatar
WayneXG95
Posts: 2565
Joined: Wed Sep 07, 2011 9:42 am
State: NSW
Location: Sydney

Re: Wayne with a Sydney 1961 FB

Post by WayneXG95 »

Cal wrote:Good stuff :clap: :clap:

What's with the XTN plates?


And for fecks sake put the plates on properly :lol:
They were on my wifes Astra so I put them on hold when I brought her Rav4
And ill do the plates later I just put them on to get home
BTW the bloody screw holds don't line up... :problem:
Wayne Chambers
President
FB EK Holden Car Club of N.S.W
Post Reply