Page 59 of 104

Re: Project 2.

Posted: Thu Apr 07, 2022 7:10 pm
by Errol62
3/8” UNF die would have been handy but yes ok. Good feeling to have that done I bet. Too many photos are never enough.


FB ute fixer upper, EK van on rotisserie

Re: Project 2.

Posted: Thu Apr 07, 2022 7:23 pm
by Brett027
Hard work putting threads on a U bolt Clay😀

Re: Project 2.

Posted: Thu Apr 07, 2022 8:32 pm
by Errol62
Yes mate. Save your energy for rubbing.

Sent from my SM-G781B using Tapatalk


Re: Project 2.

Posted: Thu Apr 07, 2022 8:43 pm
by Brett027
Excuse me?ðŸĪŠ

Re: Project 2.

Posted: Fri Apr 08, 2022 7:56 am
by funkyscooter
Can never have too many photos Brett - always good reference points for others in the future and never boring! Always a little disappointing when a build starts with where they got to, and not all the trial and error that got them there. But maybe that's just me.

Re: Project 2.

Posted: Fri Apr 08, 2022 8:12 am
by Brett027
Ha Scott, I've shown everything but my lunch in my builds😁. I'll show the back axle when brakes are in. You lot are soooo demanding🙂

Re: Project 2.

Posted: Fri Apr 08, 2022 10:02 am
by 62ekute
Brett027 wrote: Fri Apr 08, 2022 8:12 am I've shown everything but my lunch in my builds😁.
Yeah, but we know it's digestives 😁

Re: Project 2.

Posted: Fri Apr 08, 2022 10:37 am
by Brett027
Smoko is digestives. ðŸĪŠ

Re: Project 2.

Posted: Fri Apr 08, 2022 3:44 pm
by Brett027
Bit of a hold up. Went to put 2nd backing plate bits on and discovered a missing piston in the new cylinder. Glad I noticed it - otherwise would've been a big mess and lots of bad words. Off to Rares tomorrow.

Re: Project 2.

Posted: Sat Apr 09, 2022 4:50 pm
by Brett027
Finally finished rear brakes today. Very time consuming and fiddly. Turns out a couple of new Rares springs weren't quite the right shape, the adjuster plate on one side was bent, and adjusters come in a left and a right ( who would have thought?)
New handbrake cable is OK but would have been a bit better if there was an extra 2cm of shielding on each side as it's a bit stressed on the clamps - but the suspension is much lower than it will ever be on the road, so maybe not an issue.
As promised, a pic or 2 of an HR rear axle as it sits on EK springs.
An activist was using my shell for propaganda today. The irony is exquisite- given what it is and what the environment had done to it. Couldn't resist posting it.ImageImageImage

Sent from my SM-G975F using Tapatalk


Re: Project 2.

Posted: Sat Apr 09, 2022 8:09 pm
by Brett027
Wish this had been around a few months ago😀

"FE - EK Holden Ute / Wagon Rear Fuel Tank Panel
Pick up Traralgon, 3844 or can frieght
$410
Thompson Classic and replacement panels"

Re: Project 2.

Posted: Sun Apr 10, 2022 7:04 am
by Errol62
Damn

Sent from my SM-G781B using Tapatalk


Re: Project 2.

Posted: Sun Apr 10, 2022 9:06 am
by FireKraka
Double damn that is awesome I think I need one of those ðŸĪĢðŸĪĢðŸĪĢðŸĪĢ

Re: Project 2.

Posted: Sun Apr 10, 2022 12:48 pm
by Belly760
I messaged him earlier today


Sent from my iPhone using Tapatalk

Re: Project 2.

Posted: Sun Apr 10, 2022 1:00 pm
by Brett027
Boo. I wanted you to enjoy the simple pleasures of making up one of your own Sam. Lucky buggers😕