Re: Just a picture of something I’m playing with
Posted: Sat Jan 08, 2022 11:14 am
getting rid of the dizzy before next attempt?
fbekholden.com
FB-EK Holden Car Clubs of Australia
https://fbekholden.com/forum/
Just a picture of something I’m playing with
Page 5 of 9
Re: Just a picture of something I’m playing with
Posted: Sat Jan 08, 2022 11:17 am
Oh crap , that doesn't sound promising ........
Re: Just a picture of something I’m playing with
Posted: Sun Jan 09, 2022 12:20 pm
The dizzy is only an esp one out of the black carb model so nothing in it...it has crank trigger and msd programable box ( set timing with lap top) but we had problem with the ring gap being to tight, so re hone and new top rings.. try again next week... didn’t even get to rev it over 5500 but only made 220 hp and 228 ftlb still really rich and no timing in it yet see what happens next week I guess
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Re: Just a picture of something I’m playing with
Posted: Sun Jan 09, 2022 12:22 pm
Sounds like you'll need a lift to AHD
Sent from my SM-G781B using Tapatalk
Sent from my SM-G781B using Tapatalk
Re: Just a picture of something I’m playing with
Posted: Sun Jan 09, 2022 5:16 pm
Might just drive Mick’s wagon Me thinks
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Re: Just a picture of something I’m playing with
Posted: Sun Jan 09, 2022 5:23 pm
lucky you found it early - insufficient ring gap can get awful expensive 
Re: Just a picture of something I’m playing with
Posted: Sun Jan 09, 2022 11:52 pm
For sure .. we did a few runs to bed the cam in and then a little pull up to 5500 and went to have a leak test and it was blowing oil out the breather so we hooked a manometer on the breather and did a small run and found a lot of pressure so the head came straight off!!
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Re: Just a picture of something I’m playing with
Posted: Mon Jan 17, 2022 11:18 pm
I had a bit of a problem with the bonnet hinge hitting my air filter so thanks to some good info from Brodie and Mr Black here we go with the hinge conversion, had to start by getting rid of some holes and getting the mount point straight as I couldn’t live with the crooked mounting
Sent from my iPhone using Tapatalk
Re: Just a picture of something I’m playing with
Posted: Tue Jan 25, 2022 2:49 pm
Just had to make a few changes
Sent from my iPhone using Tapatalk
Re: Just a picture of something I’m playing with
Posted: Tue Jan 25, 2022 2:58 pm
Why the extension on the bottom, just to stiffen it up and brace it from sideways movement when the bonnets open ???
Re: Just a picture of something I’m playing with
Posted: Tue Jan 25, 2022 3:41 pm
Yeah that’s what I was thinking and sort of makes it look straight as well
Sent from my iPad using Tapatalk
Sent from my iPad using Tapatalk
Just a picture of something I’m playing with
Posted: Fri Apr 22, 2022 11:31 pm
Though I getter pull my finger out and get these bonnet hinges sorted out as the nationals are creeping up on me pretty quick. Considering I have a car with still no engine and no bonnet to hide the fact there is no engine in there
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Just a picture of something I’m playing with
Posted: Fri Apr 22, 2022 11:35 pm
Sent from my iPhone using Tapatalk
Re: Just a picture of something I’m playing with
Posted: Sat Apr 23, 2022 8:15 am
Nice work glen
Sent from my SM-G781B using Tapatalk
Sent from my SM-G781B using Tapatalk
Re: Just a picture of something I’m playing with
Posted: Sat Apr 23, 2022 1:09 pm
Hi Glenn,
What is the master cylinder from ???
Greg
What is the master cylinder from ???
Greg