Forgive me father for I have sinned ......
Re: Forgive me father for I have sinned ......
looks like you got a lot done after i left mate... coming up nicely
how'd the gauge panel go?
Cheers
Nathan
how'd the gauge panel go?
Cheers
Nathan
FB/EK Holden Car Club of W.A. Inc
Foundation Member
Foundation Member
Re: Forgive me father for I have sinned ......
off to a swap meet this morning , then back into it . Masked up
white base laid down
yellow bits
orange bits
unmasked
finished product
and the aforementioned bum shot Redbeard - behave yourself !!!!
also knocked up some fully sikk gauge holders ala Shake Rattle N Roll style
white base laid down
yellow bits
orange bits
unmasked
finished product
and the aforementioned bum shot Redbeard - behave yourself !!!!
also knocked up some fully sikk gauge holders ala Shake Rattle N Roll style
I started with nothing and still have most of it left.
Foundation member #61 of FB/EK Holden club of W.A.
Foundation member #61 of FB/EK Holden club of W.A.
Re: Forgive me father for I have sinned ......
Cheers NoMad , decide for yourself if it turned out good . Last job of the day was wire brush , ranex and paint the floor ready to cover with Chinamat tomorrow.
I need one of these lense covers if anyone knows of any lying around please ?????
I need one of these lense covers if anyone knows of any lying around please ?????
I started with nothing and still have most of it left.
Foundation member #61 of FB/EK Holden club of W.A.
Foundation member #61 of FB/EK Holden club of W.A.
Re: Forgive me father for I have sinned ......
ahhh nice, came out sweet... you guys did tons on the Sunday, I'm sure only a few beers were put away.
the floors should hold up to another 70 years now
Cheers
Nathan
the floors should hold up to another 70 years now
Cheers
Nathan
FB/EK Holden Car Club of W.A. Inc
Foundation Member
Foundation Member
Re: Forgive me father for I have sinned ......
Nice work Blacky. Lots of helping hands make a big difference.
Speed and Style........... One day I'll get the speed bit.
- Shain Mullavey
- Posts: 25
- Joined: Wed Jul 06, 2011 12:07 pm
- State: NT
- Location: DARWIN
Re: Forgive me father for I have sinned ......
looks like a blinker light of a old mini.
Re: Forgive me father for I have sinned ......
Yeah I think you are right , need the lens and the chrome surroundShain Mullavey wrote:looks like a blinker light of a old mini.
I started with nothing and still have most of it left.
Foundation member #61 of FB/EK Holden club of W.A.
Foundation member #61 of FB/EK Holden club of W.A.
Re: Forgive me father for I have sinned ......
FB/EK Holden Car Club of W.A. Inc
Foundation Member
Foundation Member
Re: Forgive me father for I have sinned ......
Fitted the new plates today , have managed to iron out most of the bugs, need to replace steering box and that will be about it for the mechanical side of things , still want to paint the roof and replace the left rear quarter.
I started with nothing and still have most of it left.
Foundation member #61 of FB/EK Holden club of W.A.
Foundation member #61 of FB/EK Holden club of W.A.
Re: Forgive me father for I have sinned ......
Nice one blacky have you had those plates for a while.
FB-Special
Big block 161
Holley sniper EFI.
Vintage air ducted heat and cool.
Ek auto column shift.
Lj diff and reverse lights.
WA FB~EK Car Club Member.
Big block 161
Holley sniper EFI.
Vintage air ducted heat and cool.
Ek auto column shift.
Lj diff and reverse lights.
WA FB~EK Car Club Member.
Re: Forgive me father for I have sinned ......
no mate, ordered them when I bought the car - was tossing up whether to get these or XFB-215 seeing as it was a standard but isnt too standard anymore !!!mph wrote:Nice one blacky have you had those plates for a while.
I started with nothing and still have most of it left.
Foundation member #61 of FB/EK Holden club of W.A.
Foundation member #61 of FB/EK Holden club of W.A.
Re: Forgive me father for I have sinned ......
Forgot I had his , bought it a few years back and found it today amongst a stack of other stuff
Looks cool I reckon !!
Looks cool I reckon !!
I started with nothing and still have most of it left.
Foundation member #61 of FB/EK Holden club of W.A.
Foundation member #61 of FB/EK Holden club of W.A.
Re: Forgive me father for I have sinned ......
Giving the old tart a bit of a tidy up for the nationals , went to fit me flash Rockets that i did up at Christmas and the bloody wheel studs are too short so off to Armadale Auto Parts to pick up a set of longer ones plus a set of rear shocks seeing as I replaced the rear springs that were sitting about 1/2" off the bump stops
Fitted them up
and the bastards rub that bad the car is undrivable
looks good though , even with the arse end sitting about 3 inches higher than it was ,,,,,
Decided it was time to do something about the roof , started sanding off the half sanded mess that the roof has been since i bought the car
Took some doing but its ready to hit with 180 and prime and paint tomorrow
Found out why neither back window would go down , the runner has fallen off the passengers side one and the weld that holds the slide to the runner had broken off on the drivers side. Welded the drivers one up in situ and will get some sikaflex for the passengers one tomorrow. Also fixed the inside handle on the drivers side rear door so now the hitchikers can escape !!
The headliner has split and is hanging down pretty badly so we did a cheap and cheerful repair/bodge job on it . Went to spotlight and bought some white furry stuff and glued it over whats left of the original headliner. Rough but at least its legal now and fits in with the rest of the bodgy shit
What we started with
a few safety pins and a bit of glue.......
and voila !!!!
Fitted them up
and the bastards rub that bad the car is undrivable
looks good though , even with the arse end sitting about 3 inches higher than it was ,,,,,
Decided it was time to do something about the roof , started sanding off the half sanded mess that the roof has been since i bought the car
Took some doing but its ready to hit with 180 and prime and paint tomorrow
Found out why neither back window would go down , the runner has fallen off the passengers side one and the weld that holds the slide to the runner had broken off on the drivers side. Welded the drivers one up in situ and will get some sikaflex for the passengers one tomorrow. Also fixed the inside handle on the drivers side rear door so now the hitchikers can escape !!
The headliner has split and is hanging down pretty badly so we did a cheap and cheerful repair/bodge job on it . Went to spotlight and bought some white furry stuff and glued it over whats left of the original headliner. Rough but at least its legal now and fits in with the rest of the bodgy shit
What we started with
a few safety pins and a bit of glue.......
and voila !!!!
I started with nothing and still have most of it left.
Foundation member #61 of FB/EK Holden club of W.A.
Foundation member #61 of FB/EK Holden club of W.A.
Re: Forgive me father for I have sinned ......
That's gotta suck with the rims, looks good with them on.
There's laws against raising lowered cars though Blacky.....
There's laws against raising lowered cars though Blacky.....
Speed and Style........... One day I'll get the speed bit.
Re: Forgive me father for I have sinned ......
How about fitting some super skinny tyres low rider style?
Been wondering about those rims. There is a set for sale needing a refurb but I don't know much about them.
Sent from my iPhone using Tapatalk
Been wondering about those rims. There is a set for sale needing a refurb but I don't know much about them.
Sent from my iPhone using Tapatalk
getting my FB ute on the road
EK van on rotisserie
EK van on rotisserie