My new Fb

Post photos of your pride and joy, or updates on your rebuild!

Moderators: reidy, Blacky

User avatar
FireKraka
Posts: 2486
Joined: Fri Jan 24, 2014 11:12 am
State: WA
Location: Serpentine, WA

Re: My new Fb

Post by FireKraka »

Great work John you are really knocking over a lot of the jobs that would have kept you from rego.
Keep up the pace like that mate and it will be on the road in no time.

Damn good fish there as well mate.

Regards
Neil
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
The Reverend FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
User avatar
59wagon
Posts: 645
Joined: Sun Jul 27, 2014 11:40 am
State: WA
Location: Shoalwater, WA

Re: My new Fb

Post by 59wagon »

Blacky wrote: Thu May 03, 2018 9:49 am nice work mate, I don't know how you can pull something off and leave the rest - I wish I could :D I woul dbe - oh well , may as well pull the wishbones off and paint them and the springs - hmm , now the rest of the crossmember is the only bit not done , better yank that too ...... and the next thing you know is the car is a bare shell and theres piles of parts stacked up to be cleaned and painted :wtf:
That might still happen, Blacky 😀 I’ll be taking more bits off to get to the chassis repairs - I just picked up some NOS upper inner control arm bushes for cheap off eBay so if I’m doing that then ......
But I’ve decided a different approach, I’m going to fix each bit as it comes off (like I did with the bumper), rather than having a pile of parts waiting for attention. I’ll have a pile of parts ready to install instead. I’ll see how that goes 😙
ardiesse
Posts: 1120
Joined: Thu Jan 19, 2017 9:57 am
State: NSW
Location: Sydney

Re: My new Fb

Post by ardiesse »

John,

Front suspension repairs is one area where the more you take things apart, the more you discover.
You may pull the front shocks and springs out only to discover that the bottom coil is broken off each front spring. And then you may find that the lower control arm bushes need to be replaced. And then it may be that what looks like loose lower control arm bushes is, in fact, the shafts loose in the crossmember. And that's totally separate from the little things like sway bar posts which break off, worn outer pivots and sloppy king pins.

I am so full of encouragement and good cheer today . . .

Because I had all this and more when I restored my FC. The previous owner said he could never get the front wheel alignment right . . .

Rob
ardiesse
Posts: 1120
Joined: Thu Jan 19, 2017 9:57 am
State: NSW
Location: Sydney

Re: My new Fb

Post by ardiesse »

Postscript: And did I mention sway bar bracket bolts which break off at the subframe?
User avatar
Errol62
Posts: 10484
Joined: Sat Dec 06, 2014 2:44 pm
State: SA
Location: Adelaide

Re: My new Fb

Post by Errol62 »

Very thorough tidy up John.


Sent from my iPhone using Tapatalk
getting my FB ute on the road
EK van on rotisserie
User avatar
59wagon
Posts: 645
Joined: Sun Jul 27, 2014 11:40 am
State: WA
Location: Shoalwater, WA

Re: My new Fb

Post by 59wagon »

ardiesse wrote:John,

Front suspension repairs is one area where the more you take things apart, the more you discover.
You may pull the front shocks and springs out only to discover that the bottom coil is broken off each front spring. And then you may find that the lower control arm bushes need to be replaced. And then it may be that what looks like loose lower control arm bushes is, in fact, the shafts loose in the crossmember. And that's totally separate from the little things like sway bar posts which break off, worn outer pivots and sloppy king pins.

I am so full of encouragement and good cheer today . . .

Because I had all this and more when I restored my FC. The previous owner said he could never get the front wheel alignment right . . .

Rob
Thanks for the “encouragement” RobImageImage
Yep, I’m prepared for the worst, I think??
I think those bits you mentioned are important so I’ll do what’s needed and the car can go for a few more decades untouched in that department. It looks like all the parts are available.
Just be ready, Rob, ‘cos I’ll be coming to you for advice!

Cheers,
John



Sent from my iPhone using Tapatalk
User avatar
59wagon
Posts: 645
Joined: Sun Jul 27, 2014 11:40 am
State: WA
Location: Shoalwater, WA

Re: My new Fb

Post by 59wagon »

Errol62 wrote:Very thorough tidy up John. ImageImage


Sent from my iPhone using Tapatalk
Thanks, Clay. You still chugging along with the you beaut’ blue Ute?


Sent from my iPhone using Tapatalk
User avatar
Errol62
Posts: 10484
Joined: Sat Dec 06, 2014 2:44 pm
State: SA
Location: Adelaide

Re: My new Fb

Post by Errol62 »

Done a bit. Getting spark, induction and exhaust sorted while I wait for wheel cylinders.


Sent from my iPad using Tapatalk
getting my FB ute on the road
EK van on rotisserie
User avatar
59wagon
Posts: 645
Joined: Sun Jul 27, 2014 11:40 am
State: WA
Location: Shoalwater, WA

My new Fb

Post by 59wagon »

After cleaning up the front bumper bar, I noticed the bumper irons didn’t fit to the sub frame very well - they had to be squeezed in about 2 or 3 inches.
I hammered out some bends that shouldn’t have been there (probably caused by the prangs that dented the chrome work) and took measurements.
With the irons installed, they should have a 27 1/2” inner measurement at the bumper connections, and a 26” inner measurement between the forward mounting holes on the sub frame, and 26 1/4” between the rear holes.
I made a CAD drawing and a bit of a jig and bent things until I got it right.

Before .....

Image

After .....

Image

The CAD drawing and jig .....

Image

Cheers

John


Sent from my iPhone using Tapatalk
User avatar
Errol62
Posts: 10484
Joined: Sat Dec 06, 2014 2:44 pm
State: SA
Location: Adelaide

Re: My new Fb

Post by Errol62 »

It just didn’t look right so I had to venture out to the shed and fig one out. Sure enoughImage there is close to an inch offset.


Sent from my iPhone using Tapatalk
getting my FB ute on the road
EK van on rotisserie
User avatar
thebrotherj
Posts: 682
Joined: Wed Aug 21, 2013 4:09 pm
State: NSW
Location: Sydney

Re: My new Fb

Post by thebrotherj »

I'm blaming Tapatalk - I think I am supposed to subscribe to each thread in order to receive updates - but I've missed a bunch of these!

Enjoying this build a lot, you've gone above and beyond to repair fiddly parts that would've had me phoning the wreckers (after shaking my head at how much old mate wants for them on eBay....)

I've just had flashbacks to such fun moments as "how to reattach sway bar D bush to overkill rust repair on subframe" and "sending things flying across the workshop when the upper pivot pin let go at the behest of a metre-long breaker bar" and "lowering the control arm to watch the spring come out in three pieces" and my most recent comparable, curse-worthy battle "making a bent front bumper from another car line up with modified subframe and bent fenders on current car".

Oh and honourable mention for "CAD", something I'm employing currently also! I might have to steal that line ;)
Cheers, keep up the great work & updates.
JD.
User avatar
thebrotherj
Posts: 682
Joined: Wed Aug 21, 2013 4:09 pm
State: NSW
Location: Sydney

Re: My new Fb

Post by thebrotherj »

ps: I noticed a stubby of VB in the pics of your front end rebuild. After my king pin incident, I highly recommend a switch to tinnies. I am still finding shards of VB stubby glass on the other side of the workshop after that event hahahaa :lol:

JD
User avatar
Harv
Posts: 5315
Joined: Mon Oct 08, 2007 2:00 pm
State: NSW
Location: Sydney, Australia

Re: My new Fb

Post by Harv »

thebrotherj wrote: Sat May 12, 2018 10:23 amOh and honourable mention for "CAD", something I'm employing currently also! I might have to steal that line ;)
CAD/CAM is an essential part of working on old Holdens. Its also a good way to use up those pesky empty VB boxes :mrgreen:

Cheers,
Harv
327 Chev EK wagon, original EK ute for Number 1 Daughter, an FB sedan meth monster project and a BB/MD grey motored FED.
User avatar
59wagon
Posts: 645
Joined: Sun Jul 27, 2014 11:40 am
State: WA
Location: Shoalwater, WA

Re: My new Fb

Post by 59wagon »

thebrotherj wrote:I'm blaming Tapatalk - I think I am supposed to subscribe to each thread in order to receive updates - but I've missed a bunch of these!

Enjoying this build a lot, you've gone above and beyond to repair fiddly parts that would've had me phoning the wreckers (after shaking my head at how much old mate wants for them on eBay....)

I've just had flashbacks to such fun moments as "how to reattach sway bar D bush to overkill rust repair on subframe" and "sending things flying across the workshop when the upper pivot pin let go at the behest of a metre-long breaker bar" and "lowering the control arm to watch the spring come out in three pieces" and my most recent comparable, curse-worthy battle "making a bent front bumper from another car line up with modified subframe and bent fenders on current car".

Oh and honourable mention for "CAD", something I'm employing currently also! I might have to steal that line ;)
Cheers, keep up the great work & updates.
JD.
Hahaha. Some funny moments there, Joe. Hopefully you haven’t done yourself any serious injuries.
I think one of the bits I enjoy most playing with these old girls is the challenges they present and working out how to overcome them.
Enjoying your Ute thread too, I don’t know too much about motors and gearboxes, so it’s been real useful.
Cheers,
John


Sent from my iPhone using Tapatalk
User avatar
59wagon
Posts: 645
Joined: Sun Jul 27, 2014 11:40 am
State: WA
Location: Shoalwater, WA

Re: My new Fb

Post by 59wagon »

thebrotherj wrote:ps: I noticed a stubby of VB in the pics of your front end rebuild. After my king pin incident, I highly recommend a switch to tinnies. I am still finding shards of VB stubby glass on the other side of the workshop after that event hahahaa :lol:

JD
I prefer stubbies to tinnies so I think I’ll live with the increased risk. Maybe I should use a stubby holder Image


Sent from my iPhone using Tapatalk
Post Reply