Rare and Exotic EK ute build.
Re: Rare and Exotic EK ute build.
I yanked the donk so I could weld up the engine mounts.
They were still a bugger to access, so the welds aren't as pretty as they could be, but they wont fall off.
Sorry about the bodgy photos, I couldn't see what I was doing there, either.
I should have dropped the front end out to weld them....oh well.
Welded in the tunnel and patched the firewall too.
Before I tacked it in I wiped the paint of from around the edge of the tunnel with thinners and wirewheeled around the edge of the floor again to make my life easier.
Fully welded it.
Then touched it up with a flapper wheel.
Ground the excess off on the firewall side.
And sanded it up.
I knocked about 1/4 inch off the seamjoint while I was at it for a little extra clearance on the back of the motor.
I ground the excess off underneath as well. What a turd of a way to spend an arvo...
I will seamseal the lapjoint underneath after I have wirewheeled the rest of the floor to keep moisture out.
They were still a bugger to access, so the welds aren't as pretty as they could be, but they wont fall off.
Sorry about the bodgy photos, I couldn't see what I was doing there, either.
I should have dropped the front end out to weld them....oh well.
Welded in the tunnel and patched the firewall too.
Before I tacked it in I wiped the paint of from around the edge of the tunnel with thinners and wirewheeled around the edge of the floor again to make my life easier.
Fully welded it.
Then touched it up with a flapper wheel.
Ground the excess off on the firewall side.
And sanded it up.
I knocked about 1/4 inch off the seamjoint while I was at it for a little extra clearance on the back of the motor.
I ground the excess off underneath as well. What a turd of a way to spend an arvo...
I will seamseal the lapjoint underneath after I have wirewheeled the rest of the floor to keep moisture out.
--------------------------------------------------------------------------------
Elwood: I bet these cops got SCMODS.
Jake: SCMODS?
Elwood: State County Municipal Offender Data System.
W.S.C.C.A.
St Marys chapter.
Elwood: I bet these cops got SCMODS.
Jake: SCMODS?
Elwood: State County Municipal Offender Data System.
W.S.C.C.A.
St Marys chapter.
Re: Rare and Exotic EK ute build.
Looking good Wot! Those tunnels sure make life easier and after a little work with a heat gun on the carpet removing/reshaping the moulded section for the internal bracing factory auto Carpet fits nicelly.
Speed and Style........... One day I'll get the speed bit.
Re: Rare and Exotic EK ute build.
Good tip, Cheers.
--------------------------------------------------------------------------------
Elwood: I bet these cops got SCMODS.
Jake: SCMODS?
Elwood: State County Municipal Offender Data System.
W.S.C.C.A.
St Marys chapter.
Elwood: I bet these cops got SCMODS.
Jake: SCMODS?
Elwood: State County Municipal Offender Data System.
W.S.C.C.A.
St Marys chapter.
Re: Rare and Exotic EK ute build.
Great stuff wot, not enough people post a blow-by-blow, helps out people who haven't yet done or are about to do the same job.
Re: Rare and Exotic EK ute build.
G'day to all what can i say that already hasn't been said.the work on this car is spot on.some people can turn rubbish into gold with such basic tools.some people are so talented and know how to use that talent. A job well done. cheers Gazza.
Re: Rare and Exotic EK ute build.
What stinky said - will be a big help for me!
Thanks for the cleaning pointers aswell.
Thanks for the cleaning pointers aswell.
Woody - UMX-282
FB EK Club WA
Foundation Member # 138
FB EK Club WA
Foundation Member # 138
Re: Rare and Exotic EK ute build.
Glad you are enjoying it, fellas, and thanks for the rap.
--------------------------------------------------------------------------------
Elwood: I bet these cops got SCMODS.
Jake: SCMODS?
Elwood: State County Municipal Offender Data System.
W.S.C.C.A.
St Marys chapter.
Elwood: I bet these cops got SCMODS.
Jake: SCMODS?
Elwood: State County Municipal Offender Data System.
W.S.C.C.A.
St Marys chapter.
- thebrotherj
- Posts: 680
- Joined: Wed Aug 21, 2013 4:09 pm
- State: NSW
- Location: Sydney
Re: Rare and Exotic EK ute build.
Enjoying this build Wot. Any updates?
-
- Posts: 3429
- Joined: Mon Dec 08, 2008 12:48 pm
- State: NOT ENTERED
- Location: Brisbane
Re: Rare and Exotic EK ute build.
he's working again so between that and his pub counter lunches he has no time
sometimes yor just better off shitting in yor hands and clapping
W.S.C.C.A
Woodstock chapter
W.S.C.C.A
Woodstock chapter
Re: Rare and Exotic EK ute build.
Barely touched it for 3 weeks, Ive had other shit keeping me busy.
I have stripped the trim off the seat to modify it as it hits the shifter, but that's about it.
Updates will be coming soon.
I have stripped the trim off the seat to modify it as it hits the shifter, but that's about it.
Updates will be coming soon.
--------------------------------------------------------------------------------
Elwood: I bet these cops got SCMODS.
Jake: SCMODS?
Elwood: State County Municipal Offender Data System.
W.S.C.C.A.
St Marys chapter.
Elwood: I bet these cops got SCMODS.
Jake: SCMODS?
Elwood: State County Municipal Offender Data System.
W.S.C.C.A.
St Marys chapter.
Re: Rare and Exotic EK ute build.
I finally got to get a start on the rust repair to the subframe today.
Started out with this....dunno who made it, Mick supplied it with the car, but it didn't go close...over 1/4 inch too deep.
Who ever makes them needs to be shot.
Piss poor repo parts shit me to tears.
Anyway, I cut it and shut it.
I trimmed it 3mm more than this pic, the first cut wasn't enough...
Made this bit for the front.
Got the side piece to fit.
The weld is horrible, Im gunna slice it out tomorrow and do it again.
There are holes drilled everywhere so I can plugweld it too.
Vicegrip display module....
Pics of it finished tomorrow.
Sorry for the lack of pics, I got distracted working.
Started out with this....dunno who made it, Mick supplied it with the car, but it didn't go close...over 1/4 inch too deep.
Who ever makes them needs to be shot.
Piss poor repo parts shit me to tears.
Anyway, I cut it and shut it.
I trimmed it 3mm more than this pic, the first cut wasn't enough...
Made this bit for the front.
Got the side piece to fit.
The weld is horrible, Im gunna slice it out tomorrow and do it again.
There are holes drilled everywhere so I can plugweld it too.
Vicegrip display module....
Pics of it finished tomorrow.
Sorry for the lack of pics, I got distracted working.
--------------------------------------------------------------------------------
Elwood: I bet these cops got SCMODS.
Jake: SCMODS?
Elwood: State County Municipal Offender Data System.
W.S.C.C.A.
St Marys chapter.
Elwood: I bet these cops got SCMODS.
Jake: SCMODS?
Elwood: State County Municipal Offender Data System.
W.S.C.C.A.
St Marys chapter.
-
- Posts: 3429
- Joined: Mon Dec 08, 2008 12:48 pm
- State: NOT ENTERED
- Location: Brisbane
Re: Rare and Exotic EK ute build.
loving it wot192
we need to stress that the mounts have to hang off the back for a red to fi!!!!!!
mine are level or a tad back and I cant run a fan
im enjoying your posts
we need to stress that the mounts have to hang off the back for a red to fi!!!!!!
mine are level or a tad back and I cant run a fan
im enjoying your posts
kmawic
Re: Rare and Exotic EK ute build.
This has been a great read. Nice work.
Re: Rare and Exotic EK ute build.
Hey Wot how dare you get distracted by working stop it now and get back to work on your ute and posting pictures mate how am I supposed to get all my ideas for my ute if you stop putting up pictures I mean come on really
Regards
Neil H
Regards
Neil H
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
The Reverend FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
Frankenstein EK V6 Ute
The Reverend FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)