Rust Panel Needed

OldMan's Lacky · Post by **OldMan's Lacky** » Sun May 27, 2012 10:27 pm

On Friday I purchased two rust floor panels for 'Pa's Ute' - the driver's side front and rear ones from Rare Spares in Canberra. Unfortunately the rust extends further down towards the diff and I am not aware of any providers who sell this panel. I cannot progress until I've sourced a replacement. I would be extremely appreciative if someone would be prepared to sell one that they have spare. Photos are attached to assist in identifying what panel I need. Obviously postage would be at my expense too. Thanking you in advance.

ash · Post by **ash** » Mon May 28, 2012 7:31 am

As long as the section isn't like tissue paper it might be easier just to patch up holes and make your own sections.

Craig Vayne does decent patch panels, unsure if he makes that section though.

Sent from my GT-I9000 using Tapatalk 2

Post by **Blacky** » Mon May 28, 2012 9:28 am

Someone must be wrecking a wagon over there and may be able to cut that piece out for ya ?

OldMan's Lacky · Post by **OldMan's Lacky** » Mon May 28, 2012 12:30 pm

Blacky wrote:Someone must be wrecking a wagon over there and may be able to cut that piece out for ya ?

I'm hoping

No wreckers in Canberra have them.

Flynn's down in Cooma have a few FB-EKs but Wayne couldn't tell me if he has a decent one so I need to pay him a visit and find out myself.

Might have to offer up an extra incentive such as one of my spare 'Holden' or 'Thomas' intake manifolds ...

EK283 · Post by **EK283** » Mon May 28, 2012 3:33 pm

Old mans lacky,

I have a sedan that may be ok in this area, I will look today and get back to you.

Regards Greg

OldMan's Lacky · Post by **OldMan's Lacky** » Mon May 28, 2012 3:36 pm

EK283 wrote:Old mans lacky,

I have a sedan that may be ok in this area, I will look today and get back to you.

Regards Greg

Cheers Greg

Danny

EK283 · Post by **EK283** » Mon May 28, 2012 4:02 pm

Danny,

This is the last usable piece I have in the car.

Second thoughts I might do it up one day,

It has a couple of holes but is far better than yours.

I will cut it out over the weekend and make double sure its ok, but its yours free if you want it.

I'm in Sydney so you know,

Regards Greg

OldMan's Lacky · Post by **OldMan's Lacky** » Mon May 28, 2012 4:16 pm

You're a legend Greg!!!! Thanks. I have relos in Sydney who could help or I'll come up and grab it myself if it turns out okay.

Are you looking for any parts/pieces?

parisian62 · Post by **parisian62** » Mon May 28, 2012 7:19 pm

Crikey! Is that what is left of your donor sedan Greg! That car has helped 'save' many others...

p.s I reckon there's heaps of good useable stuff left on it...

GusnElla · Post by **GusnElla** » Mon May 28, 2012 9:44 pm

PMSL< i dunno, i reckon she's a renovators delight!

OldMan's Lacky · Post by **OldMan's Lacky** » Mon May 28, 2012 9:50 pm

Hey hey hey ... stop putting thoughts in his mind!!! I need that panel

GusnElla · Post by **GusnElla** » Mon May 28, 2012 10:17 pm

What do you think fella's? A long weekend & a few slabs & get it runnin?

OldMan's Lacky · Post by **OldMan's Lacky** » Mon May 28, 2012 10:54 pm

Hey Greg,

Was looking at your build (great job by the way!!!) and saw this photo:

Looks a bit nude now doesn't it

OldMan's Lacky · Post by **OldMan's Lacky** » Sun Jun 03, 2012 9:16 am

Greg - PM sent. Cheers.

fbekholden.com

Rust Panel Needed

Rust Panel Needed

Re: Rust Panel Needed

Re: Rust Panel Needed

Re: Rust Panel Needed

Re: Rust Panel Needed

Re: Rust Panel Needed

Re: Rust Panel Needed

Re: Rust Panel Needed

Re: Rust Panel Needed

Re: Rust Panel Needed

Re: Rust Panel Needed

Re: Rust Panel Needed

Re: Rust Panel Needed

Re: Rust Panel Needed