EK Ute another for WA

SC00BB · Post by **SC00BB** » Tue Aug 16, 2011 1:11 pm

Cool, get that Wagon going.

WesternWagon · Post by **WesternWagon** » Tue Aug 16, 2011 7:21 pm

Cheers Dave

I would not change a thing on ya ute its awsome, maybe another diff ratio, the sound when you took off still rings sweet.

Great article in the Gasoline mag I picked it up today, awsome picks

Well done,

Cheers

Gazza

Thommo · Post by **Thommo** » Tue Aug 16, 2011 7:48 pm

Nice work on the ol' shifter

Doc Bob · Post by **Doc Bob** » Tue Aug 16, 2011 7:53 pm

Wish I'd known you were back home Gaz................could done with a cruize in the Wagon!
Back to work tomorrow

Will catch up again soon

WesternWagon · Post by **WesternWagon** » Sun Feb 05, 2012 10:50 am

Decided to give the ute floor a bit of a birthday yesterday, got some new carpet and some “Resomat”

Will give it the KBS treatment rust blast & rustcoat, needed a break from welding on the wagon anyway.

The floor is in really good nick, a few minor spots & that's it.

Cheers

Gazza

EK283 · Post by **EK283** » Sun Feb 05, 2012 11:16 am

Great floor pan there Gazza,

Should make a huge difference.

Regards Greg

WesternWagon · Post by **WesternWagon** » Sun Feb 05, 2012 3:11 pm

Wire buff found a few small holes, nothing to major, will replace floor pans next year, for now it fix & drive.

KBS System works very well & simple to use. Needs good ventilation

Gazza

WesternWagon · Post by **WesternWagon** » Tue Feb 07, 2012 8:20 pm

Reso Matt in today, seats back in tomorrow morning, Paint the new kick panels then off for a cruise.

Its much eaier to install when cut into small sections. Should have looked at the picture on the box

Pub lunch in order, I think, will be interesting to see what difference the Reso matt makes? If any.

Gazza

WesternWagon · Post by **WesternWagon** » Tue Feb 07, 2012 9:27 pm

And Aussie made

gpi · Post by **gpi** » Tue Feb 07, 2012 9:40 pm

and they do colours too

WesternWagon · Post by **WesternWagon** » Wed Feb 08, 2012 7:20 pm

Ute back on the road, new carpet & kick panels

Resomat made a big difference to the road noise

Gazza

mickhrt · Post by **mickhrt** » Wed Feb 08, 2012 7:33 pm

thats come up a treat Gaz

WesternWagon · Post by **WesternWagon** » Sat Feb 11, 2012 10:32 pm

Sending one on the many spare Grey Motor heads to the local machinists for a freshen up.

V6 valves porting ect.

A Wade 446 cam & twin Stromberg's unless I can fine some triples.

Gave the Twin manifold a clean up this arvo just need to drop the cabs of for an acid clean to remove the paint ( bloody EBay) and the a kit through both.

Fleck coat the tray internals screw the timber in and the ute is done.

Cheers

Gazza

fingers · Post by **fingers** » Sun Feb 12, 2012 8:53 am

Great article Gazza and a very sweet ute ............Fingers

OEK138 · Post by **OEK138** » Wed Feb 22, 2012 10:45 pm

WesternWagon wrote:Sending one on the many spare Grey Motor heads to the local machinists for a freshen up.

V6 valves porting ect.

A Wade 446 cam & twin Stromberg's unless I can fine some triples.

Gave the Twin manifold a clean up this arvo just need to drop the cabs of for an acid clean to remove the paint ( bloody EBay) and the a kit through both.

Fleck coat the tray internals screw the timber in and the ute is done.

Cheers

Gazza

Might struggle a bit with that intake, by the angle of the carbs it looks like it's a marine one ( engine tilted a lot more than in a car ) Just my 2c

fbekholden.com

EK Ute another for WA

Re: EK Ute another for WA

Re: EK Ute another for WA

Re: EK Ute another for WA

Re: EK Ute another for WA

Re: EK Ute another for WA

Re: EK Ute another for WA

Re: EK Ute another for WA

Re: EK Ute another for WA

Re: EK Ute another for WA

Re: EK Ute another for WA

Re: EK Ute another for WA

Re: EK Ute another for WA

Re: EK Ute another for WA

Re: EK Ute another for WA

Re: EK Ute another for WA